Expert Answers about Custom Fit Vehicle Wiring

• How To Install Tow Ready Custom Fit Vehicle Wiring # 118505 On 2009 Toyota Prius
• The item you selected, Tow Ready Custom Fit Vehicle Wiring, part # 118505, plugs in-line with the vehicles tail light connectors. You will need to access the wiring behind the tail light by removing the plastic trim pieces inside the vehicle. The connector with the Yellow wire will connect to the drivers side tail light harness. Then, you will need to connect the White wire which is the ground to a clean metal surface. You can use an existing bolt to connect the ground wire. Then, you...
  view full answer...


• How a Tow Ready Custom Fit Vehicle Wiring, part # 118498, Connects to 2011 Toyota Sienna
• When installing this Tow Ready Custom Fit Vehicle Wiring for the Toyota Sienna, 2011 part # 118498 on 2011 Toyota Sienna you are actually using your vehicles current tail light circuitry that is located at the rear of your vehicle. It sounds like your salesman was trying to explain to you that your Toyota Sienna will not be wired from the factory for trailer wiring, but if you install this custom wiring kit for your Sienna you will be good to go. Make sure you use the included inline...
  view full answer...


• Correct Wiring Configuration for the Curt T-Connector Vehicle Wiring Harness on a 2012 Ford Explorer
• When installing the Curt T-Connector Vehicle Wiring Harness # C56306 (which is custom fit for your Explorer), you will want to follow the written instructions that came with the harness and ignore the connector. The connector is not necessarily a custom fit item like the harness and instruction are.
  view full answer...


• Does Tow Ready Custom Vehicle Wiring # 118458 Require a Battery Connection, 2003 Pontiac Vibe GT
• The Tow Ready Custom Fit Vehicle Wiring, # 118458, does not require a direct connection to the battery when installing and can be used on your 2003 Pontiac Vibe GT. However, the benefit of a system that does include a direct connection to the battery, like Curt Custom Fit Vehicle Wiring, # 55057, is that it protects your vehicles sensitive wiring from too much amperage draw from the trailer lights, which could damage the electrical system on your 2003 Pontiac Vibe GT. The fuse protected...
  view full answer...


• How Does the Hopkins Custom Fit Vehicle Wiring # 33925 Install on a 2006 Kia Sportage
• In order to install this Hopkins Custom Fit Vehicle Wiring # 33925 on your 2006 Kia Sportage you will need remove the tail light wiring harness from the back of the tail lights of your vehicle and plug this unit inline with the tail light wiring harness. Basically, you will unplug the harness from the back of the tail light, plug this unit into the wiring harness from your tail lights, and then plug this unit directly into your tail light assembly.
  view full answer...


• Connection Point for Valley Custom Fit Vehicle Trailer Wiring, # 30218 for a 2004 Ford E-150 Van
• When installing the Valley Custom Fit Vehicle Wiring, # C56020, for Ford E-series vans, you will just need to plug in the connectors on the wiring harness to the connectors behind each of the tail lights. The bundle with the yellow, brown, and white wires goes to the left (driver side) tail light. The bundle with the green and white wires goes to the right (passenger side) tail light. I have included a link to the installation details for reference.
  view full answer...


• Installation of Tow Ready Custom Fit Vehicle Wiring # 118242 on 1999 Ford F-150
• The Tow Ready Custom Fit Vehicle Wiring, part # 118242 connects in-line with the main harness and the small harness that goes to the tail light. It is basically a T-connection. You will pull the two factory connectors apart, plug-in the 7-Way harness. If there is not a mounting bracket for a 7-way connector, you will need to use Mounting Bracket, part # PK12711U. I have linked a video install of a brake controller that also shows the installation of the Tow Ready Custom Fit Vehicle Wiring,...
  view full answer...


• How to Install the Hopkins Custom Fit Vehicle Wiring for a 2006 Chevy Express Cutaway Van
• The Hopkins Custom Fit Vehicle Wiring, # 31345, that you reference is the correct custom wiring for your 2006 Chevy Express Van. This unit contains a powered converter that has a direct connection to the battery so the harness does not draw all its power from your vehicle taillight wiring which will save your lights from failure. To install, first find a suitable place to mount the converter. The best place is probably near the left taillight. Attach the white ground wire on the unit to...
  view full answer...


• How Does Tow Ready Custom Fit Vehicle Wiring, # 118450 Install on a 2010 Chevy Malibu
• There are two possible trailer wiring options for the 2010 Chevy Malibu depending on which model you have. All models except the LTZ, use the Tow Ready Custom Fit Vehicle Wiring, # 118450. This is a T-One harness that plugs in line with the vehicle taillights. The connectors with the yellow wire go to the left taillight and the connectors with the green wire connect to the right taillight. The white ground wire gets attached to the bare metal surface behind the left taillight. I have included...
  view full answer...


• Locating Connection Points on a 2007 Ford E-350 Van to Install Custom Fit Vehicle Wiring # C56020
• The connection points to install the Valley Custom Fit Vehicle Wiring, # C56020, on your 2007 Ford E-350 van are located behind each of the taillights. The plugs on the connectors plug in line with those on your vehicle taillights. I have included a link to the installation details for the harness below.
  view full answer...


• Where is the Connection Point For Trailer Wiring Harness # 118384 on a 2011 Jeep Liberty
• The Tow Ready Custom Fit Vehicle Wiring, # 118384, is designed to fit if your 2011 Jeep Liberty already has a factory 7-Way and you want to replace it with a 4-Way. The connection point is located behind the factory installed 7-way trailer connector, or up by the spare tire of the Jeep Liberty (GM Jeep Liberty only). I have included a link to the installation details for reference. If your Liberty did not come with a factory 7-Way trailer connector, you will need to use Draw-Tite Custom...
  view full answer...


• How to Install a Hopkins Trailer Connector on a 2003 Honda Element
• Check out page 5 of the instructions I attached for the Tow Ready Custom Fit Vehicle Wiring # 118336. This is a different brand connector but it does the same thing as the Hopkins Custom Fit Vehicle Wiring # 43105 and installs the same way so the instructions will work for you as well. The instructions I attached show you exactly where the panels are that need to be removed and how to remove them.
  view full answer...


• How to Install Curt T-Connector Custom Fit Vehicle Wiring # C55369 on a 2001 Jeep Grand Cherokee
• The Curt T-Connector Custom Fit Vehicle Wiring, # C55369, is a T-Connector style connector meaning that it plugs into a plug on your 2001 Jeep Grand Cherokee. The connection point can be found behind the interior trim panel in the cargo area, on the driver's side. The converter box takes care of the necessary steps that need to be made to convert the signal from the 3-wire system on your Jeep to the 2-wire system used by most trailers. All you need to do is plug it in. I have included a...
  view full answer...


• Will Tekonsha 4-Pole Trailer Wiring Harness # 119250KIT Fit 2011 Mercedes-Benz GLK350
• The Tow Ready 4-Pole Trailer Wiring Harness # 119190KIT is a specified fit for your 2011 Mercedes-Benz GLK350 with multiplex wiring. This kit includes a circuit tester to simplify the process of identifying the correct wires on your GLK350 to connect to the module. All necessary connectors are included along with the required fuse and fuse holder. For reference I have linked both the written instructions and an installation video showing use of this item in another vehicle. I also included...
  view full answer...


• Location To Plug In Trailer Wiring Harness on 2004 Chevrolet G3500 Express Van
• The connection points to install a trailer wiring harness on your 2004 Chevrolet G3500 Express Van are located inside the van, below both tail lights. The Tow Ready Custom Fit Vehicle Wiring # 118392, will give you a 4-way trailer connector at the rear of your Express Van. If you are needing a 7-way connector, in addition to part # 118392, you will need to install Brake Controller 7 and 4 Way Installation Kit, part # ETBC7. I have linked a video installation of the Tow Ready Custom Fit...
  view full answer...


• Does the Custom Fit Vehicle Wiring for the 2010 Hyundia Santa Fe Provied Overload Protection
• Yes, the Tow Ready Custom Fit Vehicle Wiring for the 2010 Hyundai Santa Fe, item # 118415, is circuit protected. This means that if there is a short on the trailer the module will protect the vehicle circuitry. With the 118415 module the harness would need to be replaced in this situation. If you would like a converter that is circuit protected and can be reset in the event of a short circuit situation, you could use the ZCI Circuit Protected Vehicle Wiring Harness with Install Kit, item...
  view full answer...


• Installation Of Tow Ready Custom Fit Vehicle Wiring # 118501 On My 2011 Hyundai Tucson
• The item you selected, Tow Ready Custom Fit Vehicle Wiring, part # 118501, is designed to protect the vehicle wiring as it draws power directly from the vehicle battery. I cannot recommend attaching the power wire to the vehicle tail light harness as it could possibly overload the circuit and/or damage the vehicle wiring. You will want to find a rubber grommet on the floor of the rear cargo area. Then remove the grommet and cut a slice in the grommet to feed the power wire through. You...
  view full answer...


• Custom Trailer Wiring Harness For 2015 Chevrolet Impala LTD
• The CURT # C56188 is confirmed to fit your 2015 Chevrolet Impala, so I'm a little curious as to why you're having trouble plugging in. If you can tell me a bit more about how the plugs aren't connecting, I will be happy to look into this further. An additional converter shouldn't be necessary. The installation notes state: This custom-fit T-connector plugs into your vehicle's wiring harness, which is located in your rear cargo area (behind the driver and passenger side tail lights - inside...
  view full answer...


• What is the Correct Trailer Wiring Harness for the 2011 Kia Sorento
• A vehicle specific wiring harness is the best way to get the trailer lighting to work on your 2011 Kia Sorento. If your vehicle has the factory tow package wiring installed you will need the Tow Ready Custom Fit Vehicle Wiring, item # 118451, which will connect to existing connectors located along the frame on the passengers side near the rear tire. The instructions, see link, show pictures of the connectors you will need to use. If your vehicle does not have the factory tow package wiring...
  view full answer...


• Curt Custom Fit Vehicle Wiring for the 2008 Frontier by Nissan
• To install a 7-Way RV connector at the rear of your 2008 Nissan Frontier, you will need to start with a working 4-Way connector and then install a brake controller installation kit, # ETBC7, which has all of the wiring and parts needed to complete the installation of a brake controller and 7-Way trailer wiring. If your Frontier does not already have a 4-Way connector installed you can use the Curt T-Connector Vehicle Wiring Harness with Relays, # C56225, to install one, see instructions...
  view full answer...